Why Water Borewell Compressor Air to Be Released After Operation
Every homeowner knows the importance of a properly functioning borewell. A borewell is a water pump that supplies groundwater for household needs such as gardening, lawn watering, toilet flushing, and cleaning. The borewell is installed at a depth of one to three hundred feet to access groundwater from an aquifer. But, what if the borewell stops working? What is the best way to fix it?
The best way to fix a borewell that is not working is to air it out. Air needs to be released after the borewell’s operation to prevent potential damage to the borewell and the water supply it provides. Air is used to fill the borewell’s pipes and compressors to prevent the water from entering the pipes too quickly.
We’ve got you covered with everything you need to know about borewell air release. We’ll discuss what air release is, why it’s important, how to release air from a borewell, and how to prevent air from getting into your pipes.
Why Is It Important to Release Air From Your Water Borewell Compressor After Each Use
As you use a compressor, the pressure inside the system will decrease. This will cause the compressor to work harder and may shorten its lifetime.
If you don’t release air after using a compressor, the air may escape into the atmosphere—but not completely. Some of it will remain inside the compressor, leading to higher operating pressure and increased wear and tear on components.
In addition, air cannot be compressed. This means that if you don’t release air from the compressor after each use, some of the air that is compressed next time will be non-potable—containing impurities from the previously used compressor.
This will shorten the life of your compressor and increase your energy bills. It can even be dangerous—leading to compressor failure or fire—if not done properly.
How to Release Air From Your Water Borewell Compressor
There are multiple ways to release air from your water borewell compressor. If you have a smaller compressor—one that is around 5HP and below—you can bleed the air out of the system manually.
If you have a larger compressor—one that is above 5HP—you should use a compressor bleed kit to release the air.
If you choose to manually release the air, you will need a manometer—a device used to measure pressure—to monitor the pressure, and a valve or hose to open and close one end of the system to release pressure.
How Does a Water Borewell Compressor Work
A borewell compressor is a device that is used to increase the pressure of water within a borewell—a well drilled into an underground aquifer—to push the water up to the surface.
These compressors consist of a pump that sits at the bottom of the well and a set of heavy-duty belts and pulleys that are connected to the pump and extend to the top of the well. A motor at the top of the well then runs and operates the pump to increase the pressure of water within the well.
This allows more water to be pumped up to the surface, thus saving money on water bills.
Read Also:
Why Would I Need a Bigger Gallon Air Compressor
Why Use Synthetic Air Compressor Oil
How to Maintain Your Borewell Water Pump
If you have a borewell, you know that it’s a fairly expensive investment. So, it’s important to maintain the water pump regularly to make sure it lasts as long as possible. Here are some tips to follow in order to maintain your borewell water pump.
Inspect the impeller—The first thing you should do is check the impeller to see if it’s worn out and needs to be replaced. This can be done by simply removing the cover and looking at it—if it’s worn out, it should be replaced.
Change the filter—Another thing you should check regularly is the filter. You should check the filter regularly to see if it needs to be cleaned or replaced. If the filter is clogged with too much dirt and debris, it can damage the pump and reduce its efficiency.
Clean the pump—Cleaning the pump is also important. You can clean the pump with a brush dipped in water and 2-3 drops of dish soap. Make sure you remove all the dirt that may have accumulated in the pump and prevent it from clogging again.
If your water pump does clog, you can use a small screwdriver to clear the clog out of the impeller. Just be careful not to damage it—if you’ve cleaned it properly, this shouldn’t happen often.
Inspect the motor—The final thing you should inspect is the motor of your water pump. Check the motor for any signs of damage and replace if needed.
Conclusion
Air release is a vital process for maintaining a borewell’s working condition. Air is used to fill the pipes and compressors to prevent water from entering the pipes too quickly. It is important to air out a borewell after every use to prevent damage to the borewell and water supply.
We hope you found this article informative and easy to follow. If you enjoyed it, don’t forget to share it with others and leave a comment. Thanks for reading!
